How to install the Sprite's engine back plate, flywheel and clutch. Bugeye Build Episode 75 Published 2022-06-15 Download video MP4 360p Recommendations 18:47 How to recover the Austin Healey Sprite's dashboard and front cockpit trim! Bugeye Build Episode 113 14:59 How to install the Sprite's door liners & door latches. Polishing is done too! Bugeye Build Ep. 105 19:03 Original and Unrestored Austin-Healey Sprite | Jay Leno's Garage 09:08 Pedal box refreshed, clutch slave cylinder tips and tricks! Bugeye Build Episode 36 12:12 Sprite and Midget Rear Main Oil Seal from Mini Mania 08:53 How to refurbish the Austin Healey Sprite's front lever shocks. Bugeye Build Episode 71 18:28 How to install the oil pressure/water temperature gauge in a Frogeye Sprite. Bugeye Build Ep. 118 16:00 Austin-Healey Clutch Reassembly | Kyle's Garage - Episode 16 15:25 Calipers installed, old bushings removed, steering rack reassembled & filled. Bugeye Build Ep. 69! 20:10 ENGINE BLOCKS: Aluminum vs. Iron 14:51 Best Damaged Thread Repair? Let’s Settle This! Heli Coil, TIME-SERT, E-Z LOK, JB Weld, HHIP, Loctite 09:36 How I installed the speedometer cable in our Bugeye Sprite... and more!! Bugeye Build Episode 90 10:54 How I installed Austin Healey Sprite's rear bumpers. Bugeye Build Episode 110 34:20 Frogeye Sprite Piston Rings & Cylinder Hone (In-Situ), Austin Healey MG Midget A-Series, "Gaps" Ep.6 11:19 Tearing into the Austin Healey Sprite | Kyles Garage - Ep. 15 10:38 How I connected and routed the Sprite's bonnet wiring harness and horns. Bugeye Build Episode 119 19:32 Reassembling the Barn Sprite 948cc A-Series Engine 13:49 The Frogeye is primed & almost ready for color, plus how I paint small parts. Bugeye Build Ep 81 03:41 Bring a Trailer rat transformed to dreamy Bugeye Sprite street racer 14:35 Hardtop hardware removed! What are all those screws holding in? Bugeye Build Episode 146 Similar videos 07:35 Austin Healey Sprite intake and exhaust manifolds, starters and flywheels - Bugeye Build Episode 4 03:29 Sprite New Style Rear Main Seal - Austin Healey Service Manual 01:19 bug eye sprite engine pull 09:16 How to install the Sprite's front suspension. Bugeye Build Episode 73 09:32 How I installed the rear axle in the Sprite & measuring up the interior panels .Bugeye Build Ep. 77 11:26 How to install the Sprite's front springs with the suspension in place. Bugeye Build Episode 74 08:16 How to install the dip switch. How to clean & rebuild the Sprite's wiper motor. Bugeye Build Ep. 64 08:56 The Frogeye's engine compartment is painted, the boot cleaned and sealed. Bugeye Build Episode 41 08:54 Tearing down the Frogeye's A-series engine. Finding our bearings in Bugeye Build Episode 25 08:46 How to install the Frogeye's steering rack, steering column & front dampers. Bugeye Build Episode 72 08:47 Tie rods ends reinstalled, more bodywork on the bonnet & a general update. Bugeye Build Episode 70 06:03 The Sprite is readied for more primer, shiny bits on the engine & a book review! Bugeye Build Ep 80 12:25 How I installed seatbelts in my Frogeye Sprite & the rear axle installl is done. Bugeye Build Ep. 87 19:28 How to repair a Frogeye Sprite's seats Pt. 1! Patch panels ready to weld in. Bugeye Build Episode 48 15:16 Engine painted, ribcase gearbox cleaned, and a parts order unboxed! Bugeye Build Episode 66 10:25 Off the rotisserie to remove the lower rear valance & expose the boot floor! Bugeye Build Episode 26 More results